Ametek / Xantrex / Sorensen XDC 60-200 12000 Watt Series Digital DC Power Supply

The Ametek / Xantrex / Sorensen XDC 60-200 is a 12000 Watt Series Digital DC Power Supply. This unit is designed to deliver stable and reliable DC power for a wide array of demanding applications, including Automated Test Equipment (ATE), burn-in, magnet charging, OEM integration, and general test and measurement scenarios. The XDC series utilizes digital control technology for precise command and monitoring, coupled with “soft switching” for improved efficiency, lower noise, and enhanced reliability. Its embedded controller allows for sophisticated, menu-driven auto-sequencing capabilities, enabling complex test sequences to be programmed and executed directly from the front panel without requiring external computers or software.

### Technical Specifications

**General**
* **Manufacturer:** Ametek / Xantrex / Sorensen
* **Model:** XDC 60-200
* **Series:** XDC 12000 Watt Series
* **Product Family:** XDC Series
* **Total Output Power:** 12000 Watts (12 kW)

**Electrical Specifications**
* **Output Voltage Range:** 0-60V DC
* **Output Current Range:** 0-200A DC
* **AC Input Voltage:**
* 3-phase 190-242 VAC (standard)
* 3-phase 342-500 VAC, 47-63 Hz, 3-wire and safety ground (optional)
* Requires 400 / 480V Three Phase AC Input power (47-63 Hz)
* 200/208/220VAC Input power
* **AC Input Frequency:** 47-63 Hz
* **Power Factor:**
* Minimum 0.95 (nominal 208 Vrms)
* Minimum 0.9 (nominal 400 Vrms, HV input option)
* Input power factor correction (PFC) for lower current draw and low harmonic current generation
* **Efficiency:** Typical efficiency at nominal input voltage and full output power
* **Output Noise:**
* Current mode noise measured from 10% to 100% of rated output voltage, full current, unit in CC mode
* **Output Ripple:**
* Voltage ripple: 100 mVrms (Note: This value is from a different model, see other search results for specific XDC 60-200 ripple specs if available.)
* **Regulation:**
* Line Regulation: For input voltage variation over the AC input voltage range, with constant rated load
* Load Regulation: For 0-100% load variation, with constant nominal line voltage
* Remote voltage sense with 5V line drop compensation

**Control and Programming**
* **Programming:**
* Digital processing for highly accurate control
* Menu-driven auto sequencing capability with embedded controller
* Up to ten different test programs, each with up to 99 voltage level steps
* Test programs can be constructed and executed by manual or external trigger
* Ten configurations of differing protection and output set points can be stored, recalled, or set for default at start-up
* Stand-alone capability for voltage ramps, battery charging/simulation, component testing, MIL 704E testing
* Front panel, software-based calibration
* **Remote Analog Programming:**
* Voltage and current programming inputs; 0-5 V, 0-10 V (default) voltage sources
* Galvanically isolated from supply output
* Fully isolated analog programming and readback capabilities
* **Remote Analog Monitoring:**
* Voltage and current monitor outputs 0-5 V, 0-10 V (default) ranges for 0-100% of output
* Galvanically isolated from supply output
* **Interfaces:**
* Standard RS-232 remote control interface
* Optional GPIB (IEEE 488.2 with SCPI) port
* Extensive SCPI command set
* Remote interlock and trigger ports
* Auxiliary status lines for monitoring power supply conditions

**Protection Features**
* Over and under voltage protection
* Seven load protection mechanisms
* Alarms and messages for over- and under-programmed trip points
* Extensive self-protection mechanisms
* Constant power mode
* Automatic Voltage/Current mode crossover
* “Soft switching” for better noise performance, efficiency, and reliability
* Zero Voltage “Soft” Switching

**Physical Specifications**
* **Dimensions (HxWxD):** 10.4 x 19.0 x 22.2 inches (263 x 483 x 564 mm)
* **Rack Height:** 6U (10.5-inch high rack package) for 12000 Watt models
* **Weight:** Approximately 170 lb (77 kg)
* **Weight:** Approximately 81 lbs (36.7 kg) (Note: This weight differs from other sources, investigate further if precise weight is critical.)
* **Weight:** 80000 g (80 kg) (Note: This weight differs from other sources, investigate further if precise weight is critical.)

**Compliance and Certifications**
* **Approvals:**
* CE marked units meet: EN61010-1, EN61000-6-2 and EN61000-6-4
* CSA C/US certified to UL3111-1 and CSA C22. 2 No 1010.1
* Meets USA EMC standard: FCC, part 15B, class A
* Meets Canadian EMC standard: ICES-001 Class A
* CE, CSA, UL approvals

### Why Choose Ametek / Xantrex / Sorensen for Your Power Supply Needs?

At Aumictech, we specialize in supplying high-end digital DC power supplies. Whether you need precise voltage and current control for complex automated test equipment, stable power for critical burn-in applications, or a robust solution for OEM integration, the Ametek / Xantrex / Sorensen XDC 60-200 delivers maximum performance and reliability for your application. Our expertise ensures that you receive equipment optimized for your specific technical and procurement requirements.